The copper pipe is pushed into the adpater, through the threads, where a smooth snug slip fitting is located. Screw-on spouts may have threads at the back end. Some tub spouts may look like a threaded spout but in fact thread onto a brass adapter that is installed onto the pipe. They are often very small so you may find it helpful to use a flashlight to locate the screw. Step-1: There should be an Allen wrench screw in the bottom end of the bathtub spout. Is it possible to replace the pipe that the tub spout normally screws on to? This is also the case if the new spout does not fit perfectly into the old pipe. The end of the copper that will be used must be free of burrs or rough edges, when using this type of spout. Slide your new spout over the pipe and start spinning it clockwise. If the spout doesn't have a setscrew, it's a screw-on spout (Photos B and C). Wrap both ends of the new nipple with thread tape and screw it into the fitting inside the wall. Is there something else you are looking for? Our latest shed is also a pavilion—and you can build it, too! If it's been there for a while it may be a bit stubborn. The cut off end of the tube must also be free from burrs inside and out, and the edge must not be rolled inward from a dull tubing cutter. If you want to save some money, you can repair your old tub spout with the help of vinegar. Slip-on spouts slide over 1/2-in. It should easily line up to the holes of the bathtub. Make sure the pipe coming out from the wall is 1/2" Nominal (inside diameter) 5/8" outside diameter and protrudes from the finished wall surface approximately 3-1/2". How to remove and replace a threaded bathtub spout (Removal process) Step 1: Taking out the old spout with a pipe wrench. 1/2" Threaded Brass Adapter Tub Spout Example, Install a 1/2" iron pipe sized nipple so the end of the nipple projects out from the finished wall surface between 1/2" and 1-1/4". Use a 1/8" hex/Allen wrench and un tighten the Allen screw counterclockwise. Second, the threads inside the spout can crack or corrode where the spout screws onto the pipe. If the nipple is too short to grab with a wrench, use an “internal” pipe wrench ($10). These could prevent the adapter from properly connecting to the tube. Place the new Delta tub spout on the pipe threads and turn clockwise to attach. If there are burrs or rough spots on the end, use sandpaper to make the pipe smooth. In this article, we'll show you the most common types of spouts, and how to replace them. A new spout ($10 to $20) and everything else you might need are available at hardware stores and home centers. Then measure the distance from the surface of the wall to the back of the threaded elbow inside the wall. A slip-on style bathtub spout will have a setscrew, which is a small screw located on the bottom of the tub spout. or 3/4-in. To do that, soak a paper towel in vinegar, and wrap it around the tub spout. Within those two types are different attachment options: slip-on with setscrew or the threaded type. Check to make sure the pipe coming from the wall is the correct size. If it's been there for a while it may be a bit stubborn. We’ve explained how to replace a bathtub spout shower diverter, so the next move is yours. It will work as protection to what comes next, which is clamping the pipe wrench on the faucet. Ideally, the new spout will fit perfectly onto the old pipe. Most come with a bushing so they fit either 1/2-in. Depending on the age of the spout, you may need a sturdy pair of pliers or a pipe wrench to grasp the entire spout. This style will either be a front-end threaded tub spout or a rear-end threaded tub spout. Measure the length of your tub spout from the back edge of the spout to the front where the threads start on the inside of the spout. Cut any excess copper pipe so the copper pipe is not longer than 3-1/2" from the finished wall. Bathroom Ideas: Replace Tub and Shower Faucet Trim. Home House & Components Fixtures Bathtubs. Bathtub spouts can go bad in three ways: First, the tub spout diverter can wear out so it no longer blocks the water flow and sends water to the shower head. After the spout is in place, you may also want to consider running a bead of silicone caulk where the bathtub spout connects to the shower stall wall. Several models are available with a conventional diverter near the wall, or with a specialized. The Premier Online Plumbing Supplier Since 1995, Same day shipping for in-stock orders processed by 7pm EST M-F. OR - find plumbing supplies starting with: Slip-Fit (non-threaded) Tub Spout Example. Make sure the tube does not have dents, deep scratches, kinks or bends. This process should detach the fixture from the water pipe. the diverter can get worn out so that it no longer blocks the water flow to divert the water to the showerhead, the threads that connect the spout to the pipe can corrode or crack allowing water to trickle along the pipe and drip inside the wall causing damage, the finish on the spout can corrode or flake off or the finish may just need updating if you decide to change any of the other fixtures in the bathroom. Screw-on spouts have threads deep inside. Replacing a slip-on spout is easy: Just loosen the setscrew (usually with a hex wrench) and pull the spout off the copper pipe that protrudes from the wall. Replacement is the solution to any of these problems. Continue to hand tighten the tub spout until the spout is firmly against the finished wall surface. Be careful not to damage the o-ring on the outside of the brass adapter. Locate the setscrew, which is typically located on the underside of the spout, close to the wall. These particular adapters can also be used on copper tubing by sweating the adapter onto the copper pipe. Make sure the tube does not have dents, deep scratches, kinks or bends. Total the two and add 1/4 inch. increments. For example, if the spout was two inches off the wall take it apart and cut two inches off the pipe. Hand tighten adapter onto pipe nipple. Insert a large screwdriver or the handle of a wood hammer into spout, using the tool as a lever to rotate the spout in a counterclockwise direction. When I took off the old spout, I discovered it was incorrectly installed. Tighten the set screw until brass adapter is secure and unable to be rotated on the pipe. Now, measure the new bathtub pipe by placing it next to the old pipe. If so, you can try turning the spout slightly as you pull. Or use a sanitary tee and cut a pipe that fits from the outlet of tee to the fitting of the drain. Bathtub spouts may need to be replaced for a few common reasons: the diverter can get worn out so that it no longer blocks the water flow to divert the water to the showerhead; the threads that connect the spout to the pipe can corrode or crack allowing water to trickle along the pipe … I am trying to replace a bathtub diverter spout. Jun 25, 2012 - Replacing a broken bathtub spout is a simple, inexpensive project. The new spout should ft into the old pipe perfectly. Only tighten the spout by hand so you don’t damage your pipes. Thread the spout onto the pipe, start off slowly so as not to cross threads. Remove any caulking around the wall end of the tub spout with a putty knife or razor. If the pipe that protrudes from the wall is copper with a threaded fitting (Photo B), simply cut off the fitting with a tubing cutter ($10) and install a new slip-on spout (Photo A). Pull the spout from the wall with both hands. This “universal” version also has threads inside, so it can screw onto threaded pipe. You may also be able to accomplish this by placing the blade of a long screwdriver into the spout opening and using it for leverage to unscrew the threaded spout. Cool adapter and pipe with water or wet rag and make sure the o-ring groove is clean. Thread the Screw into the Retainer Ring. The setscrew might be smaller and harder to see than the one shown here; you may need a flashlight to spot it. Go to the hardware store and purchase a spout that matches those measurements. Check out our helpful video explaining the various types of tub spouts and tricks for installation, or keep reading for more detailed instructions. Finally, the spout's finish can flake off or corrode. The 1/2" IPS threaded adapter can be threaded onto galvanized, brass, stainless steel and other pipes with NPT (National Pipe Thread Taper) threads. Attach the threaded coupler to pipe (if needed). If you can see a tiny screw on the underside of the spout, you have a slip-on tub spout with a set screw. Unscrew the old nipple with a pipe wrench. Put the O-ring back into the groove on the brass adapter. Replace the Spout. Slide the tub spout on the pipe until the tub spout meets the wall. Tighten the tub spout until the spout touches the finished wall surface. Take caution to not damage the O-ring or the o-ring groove. Replacement is usually the best option for each of those issues and it is fairly simple. Before replacing your tub spout, you will need to determine which type of tub spout you have and what kind you will need to replace it. Joined: Aug 31, 2004 Location: San Diego, CA. However, try not to wiggle the spout and pipe because too much jarring may cause problems with the plumbing in the wall. The result is the overall length of the pipe … Once secured and with a firm grip, proceed to turn the wrench and the faucet in a direction counterclockwise. Step 3 - Replace the Old Pipe If Necessary Complete DIY projects like a pro! Locate the screw on the underside of the faucet or where it connects to the wall. This tub spout is constructed from metal for strength and durability in your tub/shower. Measure the drain hole from the inside of the tub to the surface the tub rests upon. A better solution is to unscrew the nipple, which is connected to an elbow just behind the wall, and replace it with a shorter one. The spout makes a convenient footrest for shaving, but that can damage the tub spout diverter or loosen pipe connections. If the pipe protrudes too far, or not far enough you will have to remove the old pipe. If so, you can try turning the brass adapter slightly to the left or right as you pull. When removing a threaded spout, place the jaws of locking pliers or a pipe wrench around the spout and tighten until secure. Loosen the screw, being careful not to drop it down the drain. Unfortunately, some are tighter than others due to caulk or internal threaded fitting. Clean off the pipe coming from the wall if there is any build-up on the pipe. In this article, we'll show you the most common types of spouts, and how to replace them. Based on the installation process of the spouts, they are of two types, namely screw-on spout and slip-on spout. I'd be worried about that connection, though. Step-2: Then, the bathtub spout will be loosely fitted with the copper tubing in the wall. Ask Question Asked 2 years, 4 months ago. Remove the tub spout. 1 Hand-turn the tub spout in a counterclockwise direction. The tub spout itself has a plastic inner core with coarse threads to match the brass adapter male threads, allowing the tub spout to have room for adjustment forward or backwards determined by the position of the adapter on the pipe. Tighten the tub spout until the spout is firmly against the finished wall surface. It mostly gets stuck due to calcification, and one efficient way that removes the calcification is vinegar. Thanks for any advice you can provide! Make sure that your new spout is the same length as your old one to avoid having to adjust the pipes or use an adapter. Jan 26, 2015 - Replacing a broken bathtub spout is a simple, inexpensive project. If it's really stubborn, you can insert a screwdriver or a wrench into the tub spout opening for leverage, and turn the spout to loosen it. The Allen screw does not need to be removed all of the way out of the brass adapter, just loosened enough to allow the brass adapter to slide off of the copper pipe. We recommend our users to update the browser. A careful removal procedure will ensure a rapid and proper replacement of the spout. Note: If your pipe nipple projects out the maximum of 1-1/4" as described in step 1, the brass adapter will thread on approximately 1/2" leaving the back of the brass adapter less than a 1" projection from the wall. First look under the spout. Twist the old spout counterclockwise to remove it. A front end threaded tub spout can be used with either a tub valve without a shower, or with a tub valve that has a shower diverter built into the tub valve. As Packy said you can add a few wraps of Teflon or you could use a bit of pipe dope, that'll lubricate the threads and let you tighten the spout a bit further. Just slide the new bathtub spout over the pipe nipple and secure it into place with the screw set. How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Use a hacksaw to cut the extra length. (Replacement process) Then slide on the new spout and tighten the setscrew. Viewed 490 times 6. There are two basic types of tub spouts: diverter style that allows you to send the flow of the water to either the tub spout or the shower with a diverter right on the tub spout and non-diverter style that flows only from the tub spout into the tub. Then slide on the new spout and tighten the setscrew. Unscrew the tub spout in a counterclockwise rotation until the tub spout is removed off of the brass adapter. They can connect to a copper threaded fitting or to steel pipe. Sign up for our newsletter! If your new bathtub spout employs a screw set system, installation is very easy to complete. These are the three most common types of spouts. Place a towel over the spout and continue tightening with adjustable pliers so that the spout is tight to the wall and the opening faces downward into the tub. Unthread and remove the spout. If there is no set screw, you have a threaded tub spout. Tighten the Screw, forcing it to break through the Extension Nipple. There are two types of brass adapters, either a 1/2" IPS (iron pipe size) threaded adapter or a 1/2" nominal inside diameter (. At first, you have to loosen it up with the help of a screwdriver. Short sections of threaded pipe (called “nipples”) are usually available in 1-in. For a screw-on spout, you should be able to twist the spout off by hand. If it doesn’t have a screw, tighten the jaws of a pipe wrench around the back of the faucet and twist it counterclockwise until it’s loose. Grab a flashlight and look beneath the tub spout while it still attached to the wall. Take care to keep solder away from the o-ring groove and the adjacent outside diameter of the groove. Screw the new spout into place. Twist the spout as you pull and be gentle so you don't loosen any pipe connections inside the wall. Once the brass adapter is secured to the pipe the tub spout is threaded onto the adapter. Rear threaded spouts can be used for either new or remodeling construction. The spout is compatible with 1/2 inch copper slip, 3/4 inch threading and 1/2 inch threading, and 1/2 inch nose threading. If you don’t have time to the job yourself, or you’d prefer not … Caution: over tightening the set screw can dent the tube. Align the Screw with recessed hole on the Extension Nipple. The new spout should ft into the old pipe perfectly. Top 10 Best Replace Bathtub Spout Pipe On The Market Product NamesProduct ImagesCheck Price#1 American Standard 060340-0990A Wall Mount Spout Diverter with... To have the best assessments and give lists of the Best Replace Bathtub Spout Pipe, we analyze a lot of user reviews. Finish tightening the adapter with a standard pipe wrench, approximately 3 turns, until snug. Once the faucet is loose, you can finish unscrewing it, or sliding it out, with your hands. Turn the wrench counterclockwise to unthread the spout from the stub-out pipe. Seal around it with silicone caulk and screw on the new spout. Do not over tighten. The slip-fit tub spout is designed to slip onto a 1/2" copper pipe without the use of any threads. Push the brass adapter onto the tube so that the threaded end touches the finished wall surface. Slip-On (non-threaded) Brass Adapter Slip-On Tub Spout Example. Be careful not to damage the o-ring on the outside of the brass adapter. Turn the wrench counterclockwise until the spout is free. Use it as leverage to loosen the faucet. Then secure the spout by tightening the setscrew. We are no longer supporting IE (Internet Explorer) as we strive to provide site experiences for browsers that support new web standards and security practices. Use a flathead or Phillips screwdriver to remove the screw. Use a large pipe wrench to remove the spout by securing the wrench over the tub spout and turning it counterclockwise to loosen. Depending on the spout you have, you might solder a copper or brass threaded connection onto a copper pipe, and screw that in and test...if it seals, cut off the excess and install the new spout. Quick Tips: Before turning the spout, make sure the setscrew is loosened completely. A threaded tub spout will not have a setscrew, and will twist off of the nipple or pipe. If the spout is now sticking out too far pull it all apart and cut the new piece of pipe the amount that the spout was sticking out from the wall. There's also a chance that the threads are too corroded for you to screw on a new spout. Replace bathtub faucet – There’s probably an ugly bathtub faucet somewhere around your house or an old bath faucet that’s leaking and doesn’t work anymore, or maybe your bathtub faucet is no longer diverting water to the shower head. Take care to not damage the O-ring on the brass adapter. Apply heat and solder adapter to the pipe. There should not be any space left between the spout and the wall. Twist the spout as you pull and be gentle so you don't loosen any pipe connections inside the wall. Hand tighten the tub spout onto the brass adapter. Tip: Place a rag or duct tape between the spout and the jaws of the tool to keep from scratching the spout. Replacing spout on irregular bathtub pipe. If you see a setscrew (Photo A), you have a “slip-on” spout. pipe. Step 9. Using a pipe wrench, grip the spout and unthread the spout from the stub-out pipe. It is really a piece of cake, as what you need to do is placing the wrench around the spout and twisting it off counterclockwise to unthread. The pipe restricts the water and it can back up and come out of the showerhead when you are using the spout to fill the tub. Sweat/Solder Brass Adapter Tub Spout Example. 1. The cut off end of the tube must also be free from burrs inside and out, and the edge must not be rolled inward from a dull tubing cutter. Apply flux to the pipe and to the inside of the brass adapter and slip the brass adapter onto the pipe so that the threaded end (wall side) is between 1/2" to 1-1/4" away from the finished wall surface. Tighten the spout a minimum of one additional turn or until all slack is taken up between the tub spout and the wall. Slide the Retainer Ring Assembly onto the Extension Nipple. First, start by wrapping the clean towel around the faucet. Determine which tool you will need to remove the screw; most will require a hex/Allen wrench, some may use a small Philips head or flathead screwdriver. If the spout could not be removed by hand after the steps above, then the next step: Insert a screwdriver into the opening where the water would flow out, and turn it like a lever. Place the new overflow drain cover against the bathtub’s overflow opening and line up the screw holes. First, carefully scrape away any residual caulk where the spout and wall meet. The back of the brass adapter (male outside thread portion) must not project more than 1" from the finished wall surface. Then, pull it out. Unfortunately , there is every liklehood that the copper stub out is … If the spout is pointing any other direction than down, rotate the spout counterclockwise until it does. This is also the case if the new spout does not fit perfectly into the old pipe. But before you buy a new spout, determine what type you need. If you’ve bought a spout that maintains a distance of 1/2 inch while sliding over the tub’s pipe and across the copper pipe, then it’s a slip-on spout. There should not be any space left between the spout and the wall. Replacing a slip-on spout is easy: Just loosen the setscrew (usually with a hex wrench) and pull the spout off the copper pipe that protrudes from the wall. Screw-on spouts can be removed by turning counterclockwise. If the pipe protrudes too far, or not far enough you will have to remove the old pipe. According to EMI Supply, pipe nipple lengths vary by 1/2 inch, so if you have a 3-inch nipple that's too long, replace it with a 2 1/2-inch one. Place the heat source where you want the solder to flow to. Expert Tips for an Easy Faucet Installation, How to Repair a Single-Handle Kitchen Faucet, How to Stop a Freeze-Proof Faucet From Leaking, 10 Tips for Installing a Faucet the Easy Way, How to Install a Frost-Proof Outdoor Faucet, We are no longer supporting IE (Internet Explorer), 9 Ways to Keep Your Dog Active Inside During the Winter, How to Remove a Bathtub Drain in 3 Easy Steps, How to Easily Dry the Inside of Latex Cleaning Gloves, Do Not Sell My Personal Information – CA Residents. Removing a threaded tub spout really is as easy as just unscrewing it! Apply some silicone caulking around the edge of the where the pipe meets the wall to prevent water from dripping behind the spout and into the shower wall. For slip-on tub spouts, your copper pipe should be a. They cost less than $2 each, so buy a couple of different lengths and save yourself a trip back to the store. Keep screwing in the faucet until it’s very difficult to turn. If the pipe coming out of the wall is steel (Photo C), you need a new screw-on spout. Make sure the hole in the tub meets the drain fitting. Make sure the pipe coming out from the wall is 1/2" Nominal (inside diameter) 5/8" outside diameter and protrudes from the finished wall surface 2" to 4". These could prevent the adapter from properly connecting to the tube. Place a pipe wrench or channel-lock pliers around the spout and tighten it, so it grips the fixture. Water can then trickle along the pipe and drip inside the wall. Attach spout to pipe, or threaded coupler. It comes complete with adapters, and pipe thread tape for an easy and seamless installation. Remove the O-ring from the brass adapter. Adman adman, Apr 1, 2007 #1. jimbo Plumber. Once the setscrew is loose, use both hands to pull the tub spout straight out, away from the wall. Tighten until snug and be sure to line up the spout vertically with the rest of the fixtures. The wall end spout (also called "rear-threaded" spout) offers added convenience because it can be connected to a tub spout stub-out nipple (1/2" or 3/4") at the wall end of the spout with a Celcon bushing. Note the measurement. Plumbers tell us that leg-shaving is the leading cause of tub spout trouble. If the setscrew is still tightened onto the pipe while turning the spout, you are likely to damage the pipe coming from the wall. You can remove your tub spout by twisting it counter-clockwise to see how your existing spout is threaded, if desired, but it is recommended you leave the spout on if you might need to use the tub before your new spout arrives. Either way, you'll have to remove the old pipe (Photo 1) and screw in a new pipe of the correct length (Photo 2). Thread the tub spout onto the brass adapter hand tight. Clean the threads and take measurements to match the new and old spout. copper pipe and fasten with a setscrew. Once the set-screw is loose, use both hands to pull the brass adapter straight out, away from the wall. Hand tighten the tub spout onto the brass adapter. Well, good news: replacing a bathtub faucet is not as difficult as it seems, but it’s important to pick the right faucet and change it properly. Active 2 years, 4 months ago. Step 3 - Replace the Old Pipe If Necessary We will now walk you through the process of replacing the bathtub spout shower diverter. But there's a good chance that the pipe protrudes too far or not far enough.